Marking a pack without a printing plate

# Marking a pack without a printing plate The date on the jar wasn't printed with the label. It was put on after filling, with a laser, into a pale window the designer had left clear. The brand panel on the label had taken a press, a proof, a varnish and an argument about a

Marking a pack without a printing plate

The date on the jar wasn't printed with the label. It was put on after filling, with a laser, into a pale window the designer had left clear. The brand panel on the label had taken a press, a proof, a varnish and an argument about a grey. The date had taken a beam and a patch of bare coating. Both were on the same jar in her hand. She asked if the next range could skip the press, since the laser was "already printing". It isn't printing, not in the sense she meant, and the shipping case beside the jar was the easier place to show why.

Plateless marks are how a plant puts a code, a date or a plain shipping text onto a pack without making a plate for something that will be wrong tomorrow. Lasers do it by changing the surface. Inkjet on the line lays a code down in ink. A thermal-transfer head does it with a ribbon, usually onto a label that then goes on a case. Each of them can carry a short, sober message. None of them is a stand-in for the panel she photographs for the retailer.

The window that worked, and the logo that didn't

He'd said yes too fast to a trial. The brand's packaging lead wanted the logo marked by the same laser as the date, so they could drop a print unit on a small shipping pack and, later, "see about the jar". The shipping pack was a plain case. The logo on the brief was the one from the jar, fine type, a specific colour, sitting in her mind on a photograph even when the case in front of them was brown board. He ran the laser on the case because the date had worked on the jar and he let that success travel further than it should have.

The date on the case was readable. The logo was a scorched drawing. No colour, no photograph, edges that thickened where the board coating varied, a grey-brown that depended on the batch of cases rather than on a swatch. Under the office lamp you could tell what it was trying to be. In a stack of the same cases you could also see that two logos didn't match each other. She still knew it was her brand. She wouldn't have put it on a shop front. He should have stopped at the date.

A laser doesn't lay ink. It darkens, or it ablates, or it foams a coating that was built to react, or it does almost nothing if the surface isn't the one somebody trialled. On coated board it can be sharp. On a plain brown case it can be pale. On some films it goes weak, or it cuts further than you wanted, or it leaves a mark that vanishes in a certain light. It will not match a brand colour. It will not carry a photograph. It will not hold a metallic. If the design only works when the grey is that grey, the laser has already lost, however clean the date looks in the window next to it.

What a coder can honestly carry

Dates, lots, times, shift codes. A barcode or a 2D code if the contrast is real, the patch is quiet, and the surface is flat enough for the scanner that will actually read it. A destination code on a shipper. A product name in plain type on a case that never goes on a shelf, where the warehouse needs to read it and the brand manager doesn't need to love it. That's the work. It's useful work, and plants still waste plates on it. A depot code that changes every week doesn't want a flexo plate and a place in the rack. It wants a head at the end of the line, or a laser on a patch that was left for it, or a thermal-transfer label if the case itself is the wrong surface.

Inkjet on the packing line is the other ordinary tool. It puts down ink, so it can be darker on a surface a laser only scorches. It can also be wiped off a damp jar, or refused by a varnish nobody mentioned, or smeared if the jar is handled before the code has settled. A barcode from a nervous head, on a moving line, is only as good as the calm in the web or the conveyor. When it's right, the warehouse scans it. When it isn't, the code is present and useless, which is a worse state than a blank patch you can still stop.

A dark brand panel is the usual way that second state happens. The date is there, in a black that disappears into the photograph, because nobody left a window and the coder was told to put it somewhere. He has a jar in the drawer where you can find the lot number if you already know it. The warehouse couldn't. They'd asked for a plateless date and they'd also asked for a picture that bled to the edge. Both requests were granted, and together they made a mark that doesn't work. The press has to leave a pale patch, or the coder has to lay a light ground and a dark code, and someone has to read the finished jar under the warehouse light. A date you can only see in the office is the same kind of failure as a logo the laser scorched. The tool did what it can do. The artwork didn't give it a place.

Thermal transfer sits in between, and people forget it counts. Ribbon onto a label, then the label onto the case or the pallet. Fine for an address and a contents line. Hopeless as a brand illustration, and dishonest if someone calls it the printed pack. It's a marking method with a substrate of its own. The ribbon, the label face and the adhesive are the process. If those aren't specified, the address is legible on Monday and scuffed by the time the pallet reaches the other site.

Simple shipping packs are where this earns its place. A brown case, one or two lines, a code, a quantity. Marking it without a plate is the sensible job. The failure starts when the case is "just shipping" in the meeting and then gets photographed, or when a retailer starts asking for the brand panel on the outers as well as on the jar. The code can stay plateless. The panel can't, not if it's the same panel as the one on the shelf. He'd watched a sister job try to save a flexo unit by having the coder print the brand name under the barcode. The barcode scanned. The name looked like a stencil. The buyer noticed before the warehouse did.

What still has to see a press

Her jar label is the list. A photograph of the fruit. A matched colour, including the grey she'd argued about, which is a mix and not a default. Fine type reversed out of a solid, small enough that a scorched edge would close the counters. A varnish used as a design, not as a coat of protection somebody forgot to mention. A foil the laser can't imitate by burning the paper around it. A panel that has to look like last year's panel under shop light in another country. That set of demands is a press, a proof and a signed sheet. A coder can visit afterwards, in the window, and add the date. It doesn't get to become the press.

There's a middle that causes the fights. A shipping case that is also a retail outer, the sort of club-shop box that is the product as far as the shopper is concerned. Plain type isn't enough, and a full press pass feels absurd for the quantity. The honest split is still available. Print the brand panel where it matters, even if that's a label applied to the case or a short digital run on the board, and mark the variable data without a plate. Don't ask one head to do both badly so the purchase order shows one supplier. He'd offered her that split on the trial case. Laser for the date and the depot code, on a pale patch. The logo left off, to be printed if the case ever needed to carry it. She was disappointed for about a minute. The scorched logo was still on the table.

Film is less forgiving than the case, and the jar's sleeve trial is where he drew the line in writing. A laser on the wrong film can brown, puncture, or leave a mark so low in contrast that the date exists only for someone who already knows where to look. A brand panel on that same film, with a photograph and a solid, still needs the press it needed last year. Leaving a clear window in the artwork is a design decision. It has to be agreed before the file is finished, not invented on the packing line by aiming the beam at whatever looks empty. They aimed at a pale area on a sample pouch once, and the beam sat across a highlight in the photograph. The date was readable. The fruit looked damaged. The pouch was a write-off, and it was a useful one.

The case, the jar, and the file he didn't send

He put the two packs side by side for the note that went back to her team. The jar keeps its printed label. The laser keeps the date, in the window, and nowhere else. The case keeps a plateless code and a contents line, and doesn't inherit the jar's logo unless someone is prepared to print it. The trial file that put the logo under the beam doesn't go to the line. He wrote that on the ticket so a helpful night shift couldn't "finish the trial" by running the rest of the pallets.

There's a cost to this honesty that sales would rather blur. Plateless marking doesn't replace a printing press in the quote. It removes a class of work the press was doing badly, or doing at a silly cost in plates. Once that work has gone, the press's queue should look more like brand panels and less like depot codes. If the queue doesn't change, the coder was an extra, not a decision. He checked the plate rack the week after the case trial. Two depot plates were still on the list for a job that now had a laser patch in the drawing. He pulled them off the list himself. Leaving them there would have meant the plant was paying for both stories.

She still uses the word printing for the date. He doesn't correct her in front of her boss. He corrects the file. The brand panel stays a press job, with the grey agreed on a signed sheet. The date stays a mark, trialled on the real surface, read under the light the warehouse uses, and kept out of the photograph. The scorched logo went in the reject bin. The clean case, code only, went in the job bag so the next person who asks to skip the press has something in their hand that isn't a promise.

Written by

Tom Ellis

Finishing

Cuts, folds, glues and binds the work after it leaves the press.

Related articles

Process

Flexo still fits packaging

# Flexo still fits packaging The buyer had been to a presentation, and he arrived wanting the range moved. Film, board, a family of labels, all of it, onto a di...

Process

Print on demand moves the stock and the cost

# Print on demand moves the stock and the cost The publisher showed me an empty bay and he was proud of it. A year ago the bay had held a title that sold steadi...

Process

Versioned packaging is a production problem

# Versioned packaging is a production problem Marketing called it a celebration. A commemorative sleeve, one brand, a dozen pictures, a few lines of type that c...

Process

Print that can be scanned, used and recovered

# Print that can be scanned, used and recovered The code scanned on the flat sheet. I watched the buyer's phone pick it up from the press table, quick and pleas...