High-viscosity inkjet on corrugated board

# High-viscosity inkjet on corrugated board The attractive version of this process is easy to say. Combined board goes under inkjet heads. The ink is water-based and thicker than the watery fluids many heads were built to throw. It sits on the liner instead of diving into it. A brown box comes off the line

High-viscosity inkjet on corrugated board

The attractive version of this process is easy to say. Combined board goes under inkjet heads. The ink is water-based and thicker than the watery fluids many heads were built to throw. It sits on the liner instead of diving into it. A brown box comes off the line already printed, without a flexo plate and without a preprint liner that still has to be corrugated afterwards. The attractive version is a demonstration. The production version is an argument with the board, with water, and with colour on a substrate that isn't white and isn't flat.

Nothing that follows depends on a viscosity figure. Thicker, here, means thick enough that the ink is being asked to do a different job from a low-viscosity jet ink: carry colourant, resist being sucked down the fibres of an open liner, and still leave the head as a drop. How a given head is persuaded to jet that fluid, often by warming it so it will flow and then letting it build body again on a cooler sheet, is a machine question. The plant question is what the board does with the drop after it lands.

Direct print on a structure, not on a sheet of paper

Preprint prints a liner while it's still a flat web, then the corrugator turns that liner into a board. The print has to survive heat, moisture, and the flute. Direct print skips that sequence. The board already exists. Liners are already glued to a fluted medium. What passes the heads is a structure: thick, already bonded, already holding a moisture balance from the corrugator, and already not flat in the way a paper web is flat.

That last point governs the head. Over each flute the liner is supported. Between flutes it can sit lower. The surface the drops meet is a set of ridges, the washboard you can see in a raking light on a plain brown box. A head has to clear the high points. Set the gap to clear every high flute, every warp, every dent, and the drop spends longer in the air, so placement on the low parts of the liner gets less certain. Set the gap tight, the way a fine image wants, and a high spot, a piece of crushed board, or a sheet that isn't lying down strikes the hardware. Paper inkjet never had to make this compromise, because paper doesn't have a flute underneath it.

The liner itself isn't one material wearing a nickname. Kraft is brown and comparatively open. Test liner, heavier in recycled fibre, varies more from making to making. White-top and mottled liners change the colour problem and don't remove the flute. Sizing, roughness, dust, and loose fibre differ by mill and by batch. Dust is a small word for a production fault. It lands on the head, it breaks a nozzle's aim, and it leaves a streak that runs with the board. A trial stack can be brushed, chosen, and unusually clean. The stack that arrives on a normal morning is the one the process has to print, and it brings the dust the trial didn't.

Warp and moisture sit under all of that. Board that left the corrugator flat can arrive at the printer curled because it gained or lost water on the way, or because the two liners weren't in balance. A curled sheet changes the gap from one side to the other. The image that was acceptable in the middle goes soft, or the head gap closes, at the edge. You don't fix that with a colour curve. You fix it by knowing the board's moisture before you promise the image, which is not a step a paper plant is in the habit of treating as part of printing.

Water has to leave, and the board notices

The carrier is water. That is the drying problem and the flatness problem in one. This isn't a system that cures by lamp and leaves the board's own moisture where the corrugator put it. Water lands in the ink film, some of it goes into the liner, and the rest has to be driven off before the sheet is stacked, die-cut, or glued. Thicker ink doesn't spare you the question. It's there so the colourant stays up. The water that brought it, and the water the liner takes in, still have to be accounted for.

Too little drying and the sheet is not a finished board. Ink sets off onto the back of the next sheet in the stack. A die-cutter smears the image, or the dust of cutting sticks in ink that is still open. Glue meets a surface that isn't in the state the glue was chosen for. The fault can wait until the pile has sat, which means you can approve a sheet at the printer and reject a stack in the morning. A trial that die-cuts three sheets by hand will not show you that wait.

Too much heat, or heat in the wrong place, attacks the reason the board was flat. The liner overdries and shrinks. The sheet curls. The adhesive that holds the flute can soften if the heat reaches it, and a flute that lets go is a board you can't call printed-and-done, however sharp the image looked. Stacks that were square become a lean. The die-cutter, which wants a flat blank, inherits the disturbance. Corrugated board is a moisture-balanced object that happens to have print on it. Wet the face and then bake it, and you have edited the balance. Getting the image dry enough to handle, without taking the board out of the window the converting line needs, is the narrow part of the process. A demonstration can live inside that window because someone is watching every sheet. A shift has to live there when nobody is watching every sheet.

There's a second water budget if you need white. Brown liner swallows a first lay. A white underprint gives the colour something to sit on, and it gives you another film of water-based ink, another drying load, and another register of white to process across a surface that isn't still. Plants get a handsome sample by flooding white on a friendly white-top board and calling the problem solved. Production kraft, ordinary and brown, reopens it. The white has to cover enough of that brown for the colour to mean what the brand signed, and it has to dry before the colour lands, and the board has to stay flat while both of those things happen.

Colour on kraft isn't a coated-paper profile with the lights down

Kraft is a coloured substrate. It isn't a dirty white. Yellows go olive. Light blues go muddy. A food photograph picks up the brown in the shadows and in any tint that was supposed to be clean. Grey balance built on a bright coated sheet doesn't describe this surface, and adjusting it by eye on one batch doesn't describe the next batch. Two mills' kraft aren't the same brown. A recycled liner can move again within what the merchant calls one grade. If the target isn't printed on the liner you will actually run, the target is a picture of a different job.

Flexo has lived with this for a long time, with plates, anilox rolls, and inks mixed for the liner. The comparison isn't that flexo is charming and inkjet isn't. The comparison is that flexo's colour is already a negotiated result on brown board, and the brand's existing pack is that result. Inkjet has to land next to it, or the brand has to accept a new result on purpose. A trial that's judged on its own, under kind light, against no previous pack, will pass a colour that fails the moment it's stood beside last month's flexo. Side by side is the test. Isolated approval is how the trial stays a trial.

Process colour on kraft also punishes the thin tints and the fine type that a head can physically place. The liner is rough. A small drop doesn't sit on a smooth coated surface. It sits on fibres, and the edge of a letter or a barcode module breaks up. Coverage that looked continuous on a smooth white sample becomes a broken film, and the brown shows through the breaks. Thicker ink is an attempt to resist that. It isn't a guarantee. The liner can still take the water and leave the colourant uneven, and a dusty patch can still knock a nozzle out and leave a streak down a panel that has nowhere to hide it. Barcodes and fine legal lines are where this stops being a matter of taste. They either scan and read, or the pack doesn't ship, however strong the photography looked in the middle of the panel.

Why a trial isn't a route

A trial is a selected stack. The liner is one making, often cleaner and flatter than the supply you'll get when the work is real. The design has been chosen, whether anyone admits it or not, to avoid the worst of the brown, the smallest type, and the heaviest water load. The operator is patient. The speed of the line is whatever lets the sample succeed, and it doesn't have to agree with a die-cutter that's waiting, because the die-cutter isn't in the trial. Inspection is by hand. A brand manager is in the room and has agreed, for today, to look at a sample rather than at a standard.

Production is the opposite of each of those kindnesses. The next boards are the ordinary ones, dust included, warp included, shade included. The design is the SKU the buyer needs, not the SKU that flatters the process. The die-cutter has a shift to run and will not pause for a sheet that's still open or still curled. Glue wants a surface in a known state. Stacks sit overnight and either set off or they don't. Next month's board has to match this month's board closely enough that the brand doesn't think you've changed the print. Flexo, for all its plates, already does that often enough that it's the thing you are being compared with. Your trial settings don't carry that variation. They carried an afternoon.

None of this says the process can't become a route. It says the route is the holding of three things at once, across ordinary board: a gap and a surface that keep the drops in place, a drying window that leaves the board fit to convert, and a colour, on that brown, that the brand has actually signed and that the next batch can meet. While any one of those is true only on a chosen stack with a person standing over it, you have a demonstration. Putting a customer's standing SKU on it is how a demonstration becomes a pile of board you can't convert and can't call the same colour as last time. Run the trial as a trial. Call it a production route when the ordinary board, the dry, and the side-by-side colour survive a shift without a special stack and a special audience.

Written by

Tom Ellis

Finishing

Cuts, folds, glues and binds the work after it leaves the press.

Related articles

Process

Flexo still fits packaging

# Flexo still fits packaging The buyer had been to a presentation, and he arrived wanting the range moved. Film, board, a family of labels, all of it, onto a di...

Process

Print on demand moves the stock and the cost

# Print on demand moves the stock and the cost The publisher showed me an empty bay and he was proud of it. A year ago the bay had held a title that sold steadi...

Process

Versioned packaging is a production problem

# Versioned packaging is a production problem Marketing called it a celebration. A commemorative sleeve, one brand, a dozen pictures, a few lines of type that c...

Process

Print that can be scanned, used and recovered

# Print that can be scanned, used and recovered The code scanned on the flat sheet. I watched the buyer's phone pick it up from the press table, quick and pleas...